构建cb嵌入式系统
本帖最后由 cubieboard 于 2014-8-23 17:17 编辑大家买Cubieboard，是用来做什么的？
很多人是买来做嵌入式的。
但是现在的系统，安卓拿去做嵌入式？不好 debian？也不好 cbos？这个压根不是给嵌入式设计的，是给新手或老手方便使用的
lubuntu？ 卡啊卡……更不行
于是我就设想弄个小点的系统，能联网，能干嘛的，满足最小需求即可
Then，我开始了我的系统构建之路，构建出了一个30多M大小的系统——BusyOS（在cbos上进一步安装）
但是，我现在可不满足于这个了，当初定义是作为维修系统，现在就不是了，毕竟作为嵌入式，谁还要CbOS啊
我决定做出个真正的busyOS，并把它安装在nand里，嵌入式难道还插sd卡？
我还准备给它弄一些功能
于是呢，我开始制作咯～
【以上写于2013 9 14 22:23】
1、直接下载：
shell：还未推出
2、以下分享过程：
http://blog.csdn.net/sara4321/article/details/8844715]
1.先把cbos安装到sd里，启动
2.下载busybox（以下可能简称bb）
Link：http://busybox.net/downloads/
3.解压&into
[*]tar xjvf busy*
[*]cd busy*
4.make menuconfig然后慢慢选
如果你想用ssh连接你的cb而非telnet，请在Login/Password Management Utilities选中
Support for PAM (Pluggable Authentication Modules)
5.make然后慢慢等
6.借助cbos的nand安装程序，把cbos安装到nand（这是为了等下改）
7.poweroff一下然后看看能不能bot
8.进SD系统
rm -rf掉除boot boot2以外其他东西（lib可以保留）
[*]
[*]mount /dev/nandb /mnt
[*]cd ~/busy*
[*]cp -Rv _install/* /mnt
[*]cp -Rv examples/bootfloppy/etc /mnt
[*]chroot /mnt ash
[*]mkdir /dev /proc /sys /var /home /tmp /mnt /run
[*]exit
[*]
修改/mnt/etc/fstab：
[*]proc /proc proc nosuid,noexec,nodev 0 0
[*]sysfs /sys sysfs nosuid,noexec,nodev 0 0
[*]devpts /dev/pts devpts gid=4,mode=620 0 0
[*]tmpfs /tmp tmpfs defaults 0 0
[*]devtmpfs /dev devtmpfs mode=0755,nosuid 0 0
[*]
[*]/dev/nanda /boot vfat defaults 0 2
[*]
[*]/dev/nandb / ext2 defaults,noatime 0 1
启动，然后发现可以进入了，log：
[*]?HELLO! BOOT0 is starting!
[*]boot0 version : 1.5.0
[*]dram size =1024
[*]Succeed in opening nand flash.
[*]Succeed in reading Boot1 file head.
[*]The size of Boot1 is 0x00056000.
[*]The file stored in 0X00000000 of block 2 is perfect.
[*]Check is correct.
[*]Ready to disable icache.
[*]Succeed in loading Boot1.
[*]Jump to Boot1.
[*][ 0.178] boot1 version : 1.5.0
[*][ 0.178] pmu type = 3
[*][ 0.179] bat vol = 0
[*][ 0.211] axi:ahb:apb=3:2:2
[*][ 0.211] set dcdc2=1400, clock=1008 successed
[*][ 0.213] key
[*][ 0.226] no key found
[*][ 0.226] flash init start
[*][ 0.258] flash init finish
[*][ 0.261] fs init ok
[*][ 0.262] fattype FAT12
[*][ 0.262] fs mount ok
[*][ 0.268] script finish
[*][ 0.269] power finish
[*][ 0.269] storage_type=0
[*][ 0.279] BootMain start
[*][ 0.279] 0
[*][ 0.312] key value = 0
[*][ 0.312] recovery key high 6, low 4
[*][ 0.313] unable to find fastboot_key key_max value
[*][ 0.321] test for multi os boot with display
[*][ 0.323] logo name is invalid or dont need show logo
[*][ 0.328] load kernel start
[*][ 0.355] load kernel successed
[*][ 0.355] start address = 0x4a000000
[*][ 0.357] jump to
[*]
[*]
[*]U-Boot 2013.01-05530-g8843079-dirty (Feb 04 2013 - 02:41:41) Allwinner Technology
[*]
[*]Board: Cubieboard
[*]I2C: ready
[*]DRAM:1 GiB
[*]NAND:0 MiB
[*]MMC: SUNXI SD/MMC: 0
[*]MMC init failed
[*]Using default environment
[*]
[*]In: serial
[*]Out: serial
[*]Err: serial
[*]Net: wemac
[*]Hit any key to stop autoboot:0
[*]** File not found /boot/uEnv.txt **
[*]reading /uEnv.txt
[*]** Unable to read file /uEnv.txt **
[*]261 bytes read in 12 ms (20.5 KiB/s)
[*]Jumping to /boot.scr
[*]## Executing script at 44000000
[*]** Bad device mmc 0 **
[*]** Bad device mmc 0 **
[*]Wrong Image Format for bootm command
[*]ERROR: can't get kernel image!
[*]4189696 bytes read in 265 ms (15.1 MiB/s)
[*]## Booting kernel from Legacy Image at 48000000 ...
[*] Image Name: Linux-3.4.43
[*] Created: 2013-08-1310:45:14 UTC
[*] Image Type: ARM Linux Kernel Image (uncompressed)
[*] Data Size: 4189632 Bytes = 4 MiB
[*] Load Address: 40008000
[*] Entry Point:40008000
[*] Verifying Checksum ... OK
[*] Loading Kernel Image ... OK
[*]OK
[*]
[*]Starting kernel ...
[*]
[*]<6>Booting Linux on physical CPU 0
[*]<6>Initializing cgroup subsys cpuset
[*]<5>Linux version 3.4.43 (root@tll-MacBookPro) (gcc version 4.7.3 (Ubuntu/Linaro 4.7.3-1ubuntu1) ) #7 PREEMPT Tue Aug 13 18:45:02 CST 2013
[*]CPU: ARMv7 Processor revision 2 (ARMv7), cr=10c5387d
[*]CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[*]Machine: sun4i
[*]<6>Memory cut off:
[*]<6> MALI : 0x5c000000 - 0x5fffffff(64 MB)
[*]<4>Ignoring unrecognised tag 0x00000000
[*]<6>Memory Reserved:
[*]<6> SYS: 0x43000000 - 0x4300ffff(64 kB)
[*]<6> VE : 0x44000000 - 0x48ffffff(80 MB)
[*]<6> G2D: 0x49000000 - 0x49ffffff(16 MB)
[*]<6> LCD: 0x5a000000 - 0x5bffffff(32 MB)
[*]Memory policy: ECC disabled, Data cache writeback
[*]<6>chip-id: A10 (AW1623 revision C)
[*]<7>On node 0 totalpages: 245760
[*]<7>free_area_init_node: node 0, pgdat c07c0260, node_mem_map c097b000
[*]<7>Normal zone: 1520 pages used for memmap
[*]<7>Normal zone: 0 pages reserved
[*]<7>Normal zone: 176656 pages, LIFO batch:31
[*]<7>HighMem zone: 528 pages used for memmap
[*]<7>HighMem zone: 67056 pages, LIFO batch:15
[*]<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768<c>
[*]<7>pcpu-alloc: <c> <c>0 <c>
[*]Built 1 zonelists in Zone order, mobility grouping on.Total pages: 243712
[*]<5>Kernel command line: console=ttyS0,115200 root=/dev/nandb rootwait loglevel=8 panic=10
[*]<6>;PID hash table entries: 4096 (order: 2, 16384 bytes)
[*]<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[*]<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[*]<6>Memory: 448MB 512MB = 960MB total
[*]<5>Memory: 833668k/833668k available, 149372k reserved, 270336K highmem
[*]<5>Virtual kernel memory layout:
[*] vector: 0xffff0000 - 0xffff1000 ( 4 kB)
[*] fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
[*] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[*] lowmem: 0xc0000000 - 0xef800000 ( 760 MB)
[*] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[*] modules : 0xbf000000 - 0xbfe00000 (14 MB)
[*] .text : 0xc0008000 - 0xc074ade0 (7436 kB)
[*] .init : 0xc074b000 - 0xc0775000 ( 168 kB)
[*] .data : 0xc0776000 - 0xc07c6020 ( 321 kB)
[*] .bss : 0xc07c6044 - 0xc097a588 (1746 kB)
[*]<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[*]<6>NR_IRQS:128
[*]<6>timer0: Periodic Mode
[*]<6>sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[*]<6>Console: colour dummy device 80x30
[*]<6>Calibrating delay loop... <c>1001.88 BogoMIPS (lpj=5009408)
[*]<6>pid_max: default: 32768 minimum: 301
[*]<6>Mount-cache hash table entries: 512
[*]<6>Initializing cgroup subsys cpuacct
[*]<6>Initializing cgroup subsys devices
[*]<6>Initializing cgroup subsys freezer
[*]<6>Initializing cgroup subsys blkio
[*]<6>CPU: Testing write buffer coherency: ok
[*]<6>hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[*]<6>Setting up static identity map for 0x40501838 - 0x40501890
[*]<6>devtmpfs: initialized
[*]<6>dummy:
[*]<6>NET: Registered protocol family 16
[*]<6>hw-breakpoint: debug architecture 0x4 unsupported.
[*]<6>Init eGon pin module V2.0
[*]SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
[*]<6>Initialize DMAC OK
[*]<6>bio: create slab <bio-0> at 0
[*]<5>SCSI subsystem initialized
[*]<7>libata version 3.00 loaded.
[*]<6>usbcore: registered new interface driver usbfs
[*]<6>usbcore: registered new interface driver hub
[*]<6>usbcore: registered new device driver usb
[*]<6>Linux video capture interface: v2.00
[*]<6>Advanced Linux Sound Architecture Driver Version 1.0.25.
[*]<6>Switching to clocksource aw 64bits couter
[*]<5>FS-Cache: Loaded
[*]<6>CacheFiles: Loaded
[*]<6>cfg80211: Calling CRDA to update world regulatory domain
[*]: CONFIG_USB_SW_SUN4I_USB0_HOST_ONLY
[*]: usb host driver initialize........
[*]: open_usb_clock
[*]: host_init_state = 0
[*]: platform is usb host
[*]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[*]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
[*]<6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
[*]<6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
[*]<6>hub 1-0:1.0: USB hub found
[*]<6>hub 1-0:1.0: 1 port detected
[*]: Set USB Power ON
[*]<6>NET: Registered protocol family 2
[*]<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[*]<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[*]<6>TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[*]<6>TCP: Hash tables configured (established 131072 bind 65536)
[*]<6>TCP: reno registered
[*]<6>UDP hash table entries: 512 (order: 1, 8192 bytes)
[*]<6>UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
[*]<6>NET: Registered protocol family 1
[*]<6>RPC: Registered named UNIX socket transport module.
[*]<6>RPC: Registered udp transport module.
[*]<6>RPC: Registered tcp transport module.
[*]<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
[*]<6>audit: initializing netlink socket (disabled)
[*]<5>type=2000 audit(0.299:1): initialized
[*]highmem bounce pool size: 64 pages
[*]<5>VFS: Disk quotas dquot_6.5.2
[*]Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[*]<5>NFS: Registering the id_resolver key type
[*]<6>NTFS driver 2.1.30 .
[*]<6>fuse init (API version 7.18)
[*]<6>msgmni has been set to 1100
[*]<6>alg: No test for stdrng (krng)
[*]<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[*]<6>io scheduler noop registered
[*]<6>io scheduler deadline registered
[*]<6>io scheduler cfq registered (default)
[*]<6>Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[*]<6>: used uart info.: 0x1f
[*]<6>: serial probe 0 irq 1 mapbase 0x01c28000
[*]<6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
[*][ 0.000000] Booting Linux on physical CPU 0
[*][ 0.000000] Initializing cgroup subsys cpuset
[*][ 0.000000] Linux version 3.4.43 (root@tll-MacBookPro) (gcc version 4.7.3 (Ubuntu/Linaro 4.7.3-1ubuntu1) ) #7 PREEMPT Tue Aug 13 18:45:02 CST 2013
[*][ 0.000000] CPU: ARMv7 Processor revision 2 (ARMv7), cr=10c5387d
[*][ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[*][ 0.000000] Machine: sun4i
[*][ 0.000000] Memory cut off:
[*][ 0.000000] MALI : 0x5c000000 - 0x5fffffff(64 MB)
[*][ 0.000000] Ignoring unrecognised tag 0x00000000
[*][ 0.000000] Memory Reserved:
[*][ 0.000000] SYS: 0x43000000 - 0x4300ffff(64 kB)
[*][ 0.000000] VE : 0x44000000 - 0x48ffffff(80 MB)
[*][ 0.000000] G2D: 0x49000000 - 0x49ffffff(16 MB)
[*][ 0.000000] LCD: 0x5a000000 - 0x5bffffff(32 MB)
[*][ 0.000000] Memory policy: ECC disabled, Data cache writeback
[*][ 0.000000] chip-id: A10 (AW1623 revision C)
[*][ 0.000000] On node 0 totalpages: 245760
[*][ 0.000000] free_area_init_node: node 0, pgdat c07c0260, node_mem_map c097b000
[*][ 0.000000] Normal zone: 1520 pages used for memmap
[*][ 0.000000] Normal zone: 0 pages reserved
[*][ 0.000000] Normal zone: 176656 pages, LIFO batch:31
[*][ 0.000000] HighMem zone: 528 pages used for memmap
[*][ 0.000000] HighMem zone: 67056 pages, LIFO batch:15
[*][ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[*][ 0.000000] pcpu-alloc: 0
[*][ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 243712
[*][ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/nandb rootwait loglevel=8 panic=10
[*][ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[*][ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[*][ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[*][ 0.000000] Memory: 448MB 512MB = 960MB total
[*][ 0.000000] Memory: 833668k/833668k available, 149372k reserved, 270336K highmem
[*][ 0.000000] Virtual kernel memory layout:
[*][ 0.000000] vector: 0xffff0000 - 0xffff1000 ( 4 kB)
[*][ 0.000000] fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
[*][ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[*][ 0.000000] lowmem: 0xc0000000 - 0xef800000 ( 760 MB)
[*][ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[*][ 0.000000] modules : 0xbf000000 - 0xbfe00000 (14 MB)
[*][ 0.000000] .text : 0xc0008000 - 0xc074ade0 (7436 kB)
[*][ 0.000000] .init : 0xc074b000 - 0xc0775000 ( 168 kB)
[*][ 0.000000] .data : 0xc0776000 - 0xc07c6020 ( 321 kB)
[*][ 0.000000] .bss : 0xc07c6044 - 0xc097a588 (1746 kB)
[*][ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[*][ 0.000000] NR_IRQS:128
[*][ 0.000000] timer0: Periodic Mode
[*][ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[*][ 0.000000] Console: colour dummy device 80x30
[*][ 0.010000] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408)
[*][ 0.050000] pid_max: default: 32768 minimum: 301
[*][ 0.050000] Mount-cache hash table entries: 512
[*][ 0.060000] Initializing cgroup subsys cpuacct
[*][ 0.060000] Initializing cgroup subsys devices
[*][ 0.060000] Initializing cgroup subsys freezer
[*][ 0.070000] Initializing cgroup subsys blkio
[*][ 0.070000] CPU: Testing write buffer coherency: ok
[*][ 0.070000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[*][ 0.080000] Setting up static identity map for 0x40501838 - 0x40501890
[*][ 0.090000] devtmpfs: initialized
[*][ 0.090000] dummy:
[*][ 0.090000] NET: Registered protocol family 16
[*][ 0.090000] hw-breakpoint: debug architecture 0x4 unsupported.
[*][ 0.100000] Init eGon pin module V2.0
[*][ 0.100000] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
[*][ 0.100000] Initialize DMAC OK
[*][ 0.110000] bio: create slab <bio-0> at 0
[*][ 0.110000] SCSI subsystem initialized
[*][ 0.110000] libata version 3.00 loaded.
[*][ 0.120000] usbcore: registered new interface driver usbfs
[*][ 0.120000] usbcore: registered new interface driver hub
[*][ 0.120000] usbcore: registered new device driver usb
[*][ 0.130000] Linux video capture interface: v2.00
[*][ 0.130000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[*][ 0.140000] Switching to clocksource aw 64bits couter
[*][ 0.140000] FS-Cache: Loaded
[*][ 0.140000] CacheFiles: Loaded
[*][ 0.150000] cfg80211: Calling CRDA to update world regulatory domain
[*][ 0.150000] : CONFIG_USB_SW_SUN4I_USB0_HOST_ONLY
[*][ 0.150000] : usb host driver initialize........
[*][ 0.160000] : open_usb_clock
[*][ 0.180000] : host_init_state = 0
[*][ 0.180000] : platform is usb host
[*][ 0.190000] : sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[*][ 0.200000] : sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
[*][ 0.210000] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
[*][ 0.210000] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
[*][ 0.220000] hub 1-0:1.0: USB hub found
[*][ 0.220000] hub 1-0:1.0: 1 port detected
[*][ 0.220000] : Set USB Power ON
[*][ 0.230000] NET: Registered protocol family 2
[*][ 0.230000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[*][ 0.240000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[*][ 0.250000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[*][ 0.250000] TCP: Hash tables configured (established 131072 bind 65536)
[*][ 0.260000] TCP: reno registered
[*][ 0.260000] UDP hash table entries: 512 (order: 1, 8192 bytes)
[*][ 0.260000] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
[*][ 0.270000] NET: Registered protocol family 1
[*][ 0.270000] RPC: Registered named UNIX socket transport module.
[*][ 0.280000] RPC: Registered udp transport module.
[*][ 0.280000] RPC: Registered tcp transport module.
[*][ 0.290000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[*][ 0.290000] audit: initializing netlink socket (disabled)
[*][ 0.300000] type=2000 audit(0.299:1): initialized
[*][ 0.300000] highmem bounce pool size: 64 pages
[*][ 0.310000] VFS: Disk quotas dquot_6.5.2
[*][ 0.310000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[*][ 0.320000] NFS: Registering the id_resolver key type
[*][ 0.320000] NTFS driver 2.1.30 .
[*][ 0.330000] fuse init (API version 7.18)
[*][ 0.330000] msgmni has been set to 1100
[*][ 0.340000] alg: No test for stdrng (krng)
[*][ 0.340000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[*][ 0.350000] io scheduler noop registered
[*][ 0.350000] io scheduler deadline registered
[*][ 0.350000] io scheduler cfq registered (default)
[*][ 0.360000] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[*][ 0.360000] : used uart info.: 0x1f
[*][ 0.370000] : serial probe 0 irq 1 mapbase 0x01c28000
[*][ 0.390000] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
[*]<6>console enabled
[*][ 1.030000] console enabled
[*]<6>: serial probe 1 irq 2 mapbase 0x01c28400
[*][ 1.040000] : serial probe 1 irq 2 mapbase 0x01c28400
[*]<6>sunxi-uart.1: ttyS1 at MMIO 0x1c28400 (irq = 2) is a U6_16550A
[*][ 1.070000] sunxi-uart.1: ttyS1 at MMIO 0x1c28400 (irq = 2) is a U6_16550A
[*]<6>: serial probe 2 irq 3 mapbase 0x01c28800
[*][ 1.080000] : serial probe 2 irq 3 mapbase 0x01c28800
[*]<6>sunxi-uart.2: ttyS2 at MMIO 0x1c28800 (irq = 3) is a U6_16550A
[*][ 1.110000] sunxi-uart.2: ttyS2 at MMIO 0x1c28800 (irq = 3) is a U6_16550A
[*]<6>: serial probe 3 irq 4 mapbase 0x01c28c00
[*][ 1.120000] : serial probe 3 irq 4 mapbase 0x01c28c00
[*]<6>sunxi-uart.3: ttyS3 at MMIO 0x1c28c00 (irq = 4) is a U6_16550A
[*][ 1.150000] sunxi-uart.3: ttyS3 at MMIO 0x1c28c00 (irq = 4) is a U6_16550A
[*]<6>: serial probe 4 irq 17 mapbase 0x01c29000
[*][ 1.170000] : serial probe 4 irq 17 mapbase 0x01c29000
[*]<6>sunxi-uart.4: ttyS4 at MMIO 0x1c29000 (irq = 17) is a U6_16550A
[*][ 1.200000] sunxi-uart.4: ttyS4 at MMIO 0x1c29000 (irq = 17) is a U6_16550A
[*]<7>G2D: drv_g2d_init
[*][ 1.210000] G2D: drv_g2d_init
[*]<6>G2D: g2dmem: g2d_start=49000000, g2d_size=1000000
[*][ 1.210000] G2D: g2dmem: g2d_start=49000000, g2d_size=1000000
[*]<6>G2D: head:c9000000,tail:ca000000
[*][ 1.230000] G2D: head:c9000000,tail:ca000000
[*]<6>G2D: Module initialized.major:252
[*][ 1.230000] G2D: Module initialized.major:252
[*]<6>brd: module loaded
[*][ 1.240000] brd: module loaded
[*]<6>loop: module loaded
[*][ 1.250000] loop: module loaded
[*]nand driver, init.
[*][ 1.250000] nand driver, init.
[*]cmu_clk is 480
[*][ 1.260000] cmu_clk is 480
[*]nand clk init end
[*][ 1.260000] nand clk init end
[*]offset 0xc:0x26141
[*][ 1.270000] offset 0xc:0x26141
[*]offset 0x14:0x8200000b
[*][ 1.270000] offset 0x14:0x8200000b
[*] nand gpio_request
[*][ 1.280000] nand gpio_request
[*] nand driver version: 0x2 0x9
[*][ 1.290000] nand driver version: 0x2 0x9
[*]nand interrupte register ok
[*][ 1.290000] nand interrupte register ok
[*]ret of NFC_ChangMode is 0
[*][ 1.300000] ret of NFC_ChangMode is 0
[*]dma_hdleis 0
[*][ 1.310000] dma_hdleis 0
[*]dma_hdleis 10000008
[*][ 1.310000] dma_hdleis 10000008
[*]cmu_clk is 480
[*][ 1.320000] cmu_clk is 480
[*]nand clk init end
[*][ 1.320000] nand clk init end
[*]offset 0xc:0x26141
[*][ 1.320000] offset 0xc:0x26141
[*]offset 0x14:0x82000007
[*][ 1.330000] offset 0x14:0x82000007
[*]<4>Dev nand: part 1, start 8, size 1016
[*][ 1.370000] Dev nand: part 1, start 8, size 1016
[*]<4>Dev nand: part 2, start 1024, size 7977984
[*][ 1.380000] Dev nand: part 2, start 1024, size 7977984
[*]<6> nand: nanda nandb
[*][ 1.390000]nand: nanda nandb
[*]<6>benn: nand probe enter
[*][ 1.400000] benn: nand probe enter
[*]nand driver, ok.
[*][ 1.400000] nand driver, ok.
[*]<6>wemac Ethernet Driver, V1.01 in file:drivers/net/ethernet/sun4i/sun4i_wemac.c
[*][ 1.410000] wemac Ethernet Driver, V1.01 in file:drivers/net/ethernet/sun4i/sun4i_wemac.c
[*]<6> ahb clk enable
[*][ 1.420000] ahb clk enable
[*]<6> ahb gate clk: 0x26141
[*][ 1.430000] ahb gate clk: 0x26141
[*]<4>emac MAC isn't valid!
[*][ 1.470000] emac MAC isn't valid!
[*]<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[*][ 1.470000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[*]<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[*][ 1.480000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[*]: open clock
[*][ 1.500000] : open clock
[*]: Set USB Power ON
[*][ 1.520000] : Set USB Power ON
[*]<6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[*][ 1.530000] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[*]<6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
[*][ 1.540000] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
[*]<6>sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
[*][ 1.550000] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
[*]<6>sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
[*][ 1.580000] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
[*]<6>hub 2-0:1.0: USB hub found
[*][ 1.590000] hub 2-0:1.0: USB hub found
[*]<6>hub 2-0:1.0: 1 port detected
[*][ 1.590000] hub 2-0:1.0: 1 port detected
[*]: open clock
[*][ 1.600000] : open clock
[*]<6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[*][ 1.620000] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[*]<6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
[*][ 1.640000] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
[*]<6>sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
[*][ 1.650000] sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
[*]<6>hub 3-0:1.0: USB hub found
[*][ 1.720000] hub 3-0:1.0: USB hub found
[*]<6>hub 3-0:1.0: 1 port detected
[*][ 1.730000] hub 3-0:1.0: 1 port detected
[*]: open clock
[*][ 1.730000] : open clock
[*]: Set USB Power ON
[*][ 1.760000] : Set USB Power ON
[*]<6>sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[*][ 1.760000] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[*]<6>sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
[*][ 1.780000] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
[*]<6>sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000
[*][ 1.790000] sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000
[*]<6>sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00
[*][ 1.820000] sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00
[*]<6>hub 4-0:1.0: USB hub found
[*][ 1.830000] hub 4-0:1.0: USB hub found
[*]<6>hub 4-0:1.0: 1 port detected
[*][ 1.830000] hub 4-0:1.0: 1 port detected
[*]: open clock
[*][ 1.840000] : open clock
[*]<6>sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[*][ 1.860000] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[*]<6>sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
[*][ 1.880000] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
[*]<6>sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400
[*][ 1.890000] sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400
[*]<6>hub 5-0:1.0: USB hub found
[*][ 1.960000] hub 5-0:1.0: USB hub found
[*]<6>hub 5-0:1.0: 1 port detected
[*][ 1.970000] hub 5-0:1.0: 1 port detected
[*]<6>Initializing USB Mass Storage driver...
[*][ 1.970000] Initializing USB Mass Storage driver...
[*]<6>usbcore: registered new interface driver usb-storage
[*][ 1.980000] usbcore: registered new interface driver usb-storage
[*]<6>USB Mass Storage support registered.
[*][ 1.990000] USB Mass Storage support registered.
[*]<6>usbcore: registered new interface driver ums-alauda
[*][ 2.000000] usbcore: registered new interface driver ums-alauda
[*]<6>usbcore: registered new interface driver ums-cypress
[*][ 2.010000] usbcore: registered new interface driver ums-cypress
[*]<6>usbcore: registered new interface driver ums-datafab
[*][ 2.020000] usbcore: registered new interface driver ums-datafab
[*]<6>usbcore: registered new interface driver ums_eneub6250
[*][ 2.030000] usbcore: registered new interface driver ums_eneub6250
[*]<6>usbcore: registered new interface driver ums-freecom
[*][ 2.040000] usbcore: registered new interface driver ums-freecom
[*]<6>usbcore: registered new interface driver ums-isd200
[*][ 2.060000] usbcore: registered new interface driver ums-isd200
[*]<6>usbcore: registered new interface driver ums-jumpshot
[*][ 2.070000] usbcore: registered new interface driver ums-jumpshot
[*]<6>usbcore: registered new interface driver ums-karma
[*][ 2.080000] usbcore: registered new interface driver ums-karma
[*]<6>usbcore: registered new interface driver ums-onetouch
[*][ 2.090000] usbcore: registered new interface driver ums-onetouch
[*]<6>usbcore: registered new interface driver ums-realtek
[*][ 2.100000] usbcore: registered new interface driver ums-realtek
[*]<6>usbcore: registered new interface driver ums-sddr09
[*][ 2.110000] usbcore: registered new interface driver ums-sddr09
[*]<6>usbcore: registered new interface driver ums-sddr55
[*][ 2.120000] usbcore: registered new interface driver ums-sddr55
[*]<6>usbcore: registered new interface driver ums-usbat
[*][ 2.130000] usbcore: registered new interface driver ums-usbat
[*]<6>mousedev: PS/2 mouse device common for all mice
[*][ 2.140000] mousedev: PS/2 mouse device common for all mice
[*]sunxi RTC version 0.1
[*][ 2.150000] sunxi RTC version 0.1
[*]<6>sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380248073
[*][ 2.160000] sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380248073
[*]<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[*][ 2.170000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[*]<6>sunxi-rtc sunxi-rtc: read time 2013-9-14 22:40:56
[*][ 2.180000] sunxi-rtc sunxi-rtc: read time 2013-9-14 22:40:56
[*]<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[*][ 2.190000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[*]<6>sunxi-rtc sunxi-rtc: read time 2013-9-14 22:40:56
[*][ 2.200000] sunxi-rtc sunxi-rtc: read time 2013-9-14 22:40:56
[*]<6>sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
[*][ 2.210000] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
[*]<6>i2c /dev entries driver
[*][ 2.220000] i2c /dev entries driver
[*]!!! base_Addr = 0xf1c2ac00
[*][ 2.230000] !!! base_Addr = 0xf1c2ac00
[*]config i2c gpio with gpio_config api
[*][ 2.230000] config i2c gpio with gpio_config api
[*]twi0, apb clock = 24000000
[*][ 2.240000] twi0, apb clock = 24000000
[*]<6>axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
[*][ 2.250000] axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
[*]<6>I2C: i2c-0: AW16XX I2C adapter
[*][ 2.260000] I2C: i2c-0: AW16XX I2C adapter
[*]!!! base_Addr = 0xf1c2b000
[*][ 2.270000] !!! base_Addr = 0xf1c2b000
[*]twi1, apb clock = 24000000
[*][ 2.270000] twi1, apb clock = 24000000
[*]<6>I2C: i2c-1: AW16XX I2C adapter
[*][ 2.280000] I2C: i2c-1: AW16XX I2C adapter
[*]!!! base_Addr = 0xf1c2b400
[*][ 2.290000] !!! base_Addr = 0xf1c2b400
[*]twi2, apb clock = 24000000
[*][ 2.290000] twi2, apb clock = 24000000
[*]<6>I2C: i2c-2: AW16XX I2C adapter
[*][ 2.300000] I2C: i2c-2: AW16XX I2C adapter
[*]<6>lirc_dev: IR Remote Control driver registered, major 251
[*][ 2.310000] lirc_dev: IR Remote Control driver registered, major 251
[*]<6>IR NEC protocol handler initialized
[*][ 2.320000] IR NEC protocol handler initialized
[*]<6>IR RC5(x) protocol handler initialized
[*][ 2.330000] IR RC5(x) protocol handler initialized
[*]<6>IR RC6 protocol handler initialized
[*][ 2.330000] IR RC6 protocol handler initialized
[*]<6>IR JVC protocol handler initialized
[*][ 2.340000] IR JVC protocol handler initialized
[*]<6>IR Sony protocol handler initialized
[*][ 2.350000] IR Sony protocol handler initialized
[*]<6>IR RC5 (streamzap) protocol handler initialized
[*][ 2.360000] IR RC5 (streamzap) protocol handler initialized
[*]<6>IR SANYO protocol handler initialized
[*][ 2.370000] IR SANYO protocol handler initialized
[*]<6>IR MCE Keyboard/mouse protocol handler initialized
[*][ 2.380000] IR MCE Keyboard/mouse protocol handler initialized
[*]<6>IR LIRC bridge handler initialized
[*][ 2.390000] IR LIRC bridge handler initialized
[*]: install start!!!
[*][ 2.400000] : install start!!!
[*]: install end!!!
[*][ 2.400000] : install end!!!
[*]----- avs_dev driver load... ----
[*][ 2.410000] ----- avs_dev driver load... ----
[*]----- register iomem ----
[*][ 2.420000] ----- register iomem ----
[*]--- avs_dev driver load ok!! -----
[*][ 2.430000] --- avs_dev driver load ok!! -----
[*] start!!!
[*][ 2.430000] start!!!
[*] init end!!!
[*][ 2.440000] init end!!!
[*] start!!!
[*][ 2.440000] start!!!
[*] init end!!!
[*][ 2.450000] init end!!!
[*]<6>axp20_ldo1: 1300 mV
[*][ 2.450000] axp20_ldo1: 1300 mV
[*]<6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
[*][ 2.460000] axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
[*]<6>axp20_ldo3: 700 <--> 3500 mV at 2800 mV
[*][ 2.470000] axp20_ldo3: 700 <--> 3500 mV at 2800 mV
[*]<6>axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
[*][ 2.480000] axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
[*]<6>axp20_buck2: 700 <--> 2275 mV at 1400 mV
[*][ 2.490000] axp20_buck2: 700 <--> 2275 mV at 1400 mV
[*]<6>axp20_buck3: 700 <--> 3500 mV at 1250 mV
[*][ 2.500000] axp20_buck3: 700 <--> 3500 mV at 1250 mV
[*]<6>axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
[*][ 2.510000] axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
[*]<6>input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.41/input/input0
[*][ 2.520000] input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.41/input/input0
[*]<4>axp20_ldo2: Failed to create debugfs directory
[*][ 2.550000] axp20_ldo2: Failed to create debugfs directory
[*]<6>cpuidle: using governor ladder
[*][ 2.560000] cpuidle: using governor ladder
[*]<6>cpuidle: using governor menu
[*][ 2.570000] cpuidle: using governor menu
[*]: no sdio card used in configuration
[*][ 2.580000] : no sdio card used in configuration
[*]: sunximmc_init
[*][ 2.590000] : sunximmc_init
[*]: sunxi mmc controller using config : 0xb
[*][ 2.590000] : sunxi mmc controller using config : 0xb
[*]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
[*][ 2.600000] : sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
[*]: mmc 0 power off !!
[*][ 2.610000] : mmc 0 power off !!
[*]: mmc0 Probe: base:0xf1c0f000 irq:32 dma:0 pdes:0xee808000, ret 0.
[*][ 2.620000] : mmc0 Probe: base:0xf1c0f000 irq:32 dma:0 pdes:0xee808000, ret 0.
[*]: sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1
[*][ 2.630000] : sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1
[*]: mmc 1 power off !!
[*][ 2.650000] : mmc 1 power off !!
[*]: mmc1 Probe: base:0xf1c10000 irq:33 dma:0 pdes:0xee810000, ret 0.
[*][ 2.650000] : mmc1 Probe: base:0xf1c10000 irq:33 dma:0 pdes:0xee810000, ret 0.
[*]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3
[*][ 2.670000] : sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3
[*]: mmc 3 power off !!
[*][ 2.680000] : mmc 3 power off !!
[*]: mmc3 Probe: base:0xf1c12000 irq:35 dma:0 pdes:0xee814000, ret 0.
[*][ 2.690000] : mmc3 Probe: base:0xf1c12000 irq:35 dma:0 pdes:0xee814000, ret 0.
[*]<6>sunxi_leds driver init
[*][ 2.700000] sunxi_leds driver init
[*]<7>Registered led device: green:ph20:led1
[*][ 2.710000] Registered led device: green:ph20:led1
[*]<7>Registered led device: blue:ph21:led2
[*][ 2.710000] Registered led device: blue:ph21:led2
[*]<6>ledtrig-cpu: registered to indicate activity on CPUs
[*][ 2.720000] ledtrig-cpu: registered to indicate activity on CPUs
[*]<6>usbcore: registered new interface driver usbhid
[*][ 2.730000] usbcore: registered new interface driver usbhid
[*]<6>usbhid: USB HID core driver
[*][ 2.740000] usbhid: USB HID core driver
[*]<6>logger: created 256K log 'log_main'
[*][ 2.750000] logger: created 256K log 'log_main'
[*]<6>logger: created 256K log 'log_events'
[*][ 2.760000] logger: created 256K log 'log_events'
[*]<6>logger: created 256K log 'log_radio'
[*][ 2.770000] logger: created 256K log 'log_radio'
[*]<6>logger: created 256K log 'log_system'
[*][ 2.780000] logger: created 256K log 'log_system'
[*]enter sun4i Audio codec!!!
[*][ 2.780000] enter sun4i Audio codec!!!
[*]<6>sun4i audio support initialized
[*][ 2.790000] sun4i audio support initialized
[*]sun4i Audio codec successfully loaded..
[*][ 2.800000] sun4i Audio codec successfully loaded..
[*]<6>IPv4 over IPv4 tunneling driver
[*][ 2.810000] IPv4 over IPv4 tunneling driver
[*]<6>TCP: cubic registered
[*][ 2.810000] TCP: cubic registered
[*]<6>Initializing XFRM netlink socket
[*][ 2.820000] Initializing XFRM netlink socket
[*]<6>NET: Registered protocol family 17
[*][ 2.830000] NET: Registered protocol family 17
[*]<6>NET: Registered protocol family 15
[*][ 2.840000] NET: Registered protocol family 15
[*]<6>8021q: 802.1Q VLAN Support v1.8
[*][ 2.840000] 8021q: 802.1Q VLAN Support v1.8
[*]<6>lib80211: common routines for IEEE802.11 drivers
[*][ 2.850000] lib80211: common routines for IEEE802.11 drivers
[*]<7>lib80211_crypt: registered algorithm 'NULL'
[*][ 2.860000] lib80211_crypt: registered algorithm 'NULL'
[*]<5>Registering the dns_resolver key type
[*][ 2.870000] Registering the dns_resolver key type
[*]<6>VFP support v0.3: [ 2.880000] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[*]implementor 41 architecture 3 part 30 variant c rev 3
[*]<5>Registering SWP/SWPB emulation handler
[*][ 2.890000] Registering SWP/SWPB emulation handler
[*]<4>axp20_buck2: Failed to create debugfs directory
[*][ 2.900000] axp20_buck2: Failed to create debugfs directory
[*]<6>registered taskstats version 1
[*][ 2.910000] registered taskstats version 1
[*]<4>axp20_buck3: incomplete constraints, leaving on
[*][ 2.920000] axp20_buck3: incomplete constraints, leaving on
[*]<4>axp20_buck2: incomplete constraints, leaving on
[*][ 2.930000] axp20_buck2: incomplete constraints, leaving on
[*]<4>axp20_ldo4: incomplete constraints, leaving on
[*][ 2.940000] axp20_ldo4: incomplete constraints, leaving on
[*]<4>axp20_ldo3: incomplete constraints, leaving on
[*][ 2.950000] axp20_ldo3: incomplete constraints, leaving on
[*]<4>axp20_ldo2: incomplete constraints, leaving on
[*][ 2.960000] axp20_ldo2: incomplete constraints, leaving on
[*]<6>sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[*][ 2.970000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[*]<6>sunxi-rtc sunxi-rtc: read time 2013-9-14 22:40:56
[*][ 2.980000] sunxi-rtc sunxi-rtc: read time 2013-9-14 22:40:56
[*]: mmc 3 power on !!
[*][ 2.990000] : mmc 3 power on !!
[*]<6>sunxi-rtc sunxi-rtc: setting system clock to 2013-09-14 22:40:56 UTC (1379198456)
[*][ 3.000000] sunxi-rtc sunxi-rtc: setting system clock to 2013-09-14 22:40:56 UTC (1379198456)
[*]<6>ALSA device list:
[*][ 3.010000] ALSA device list:
[*]<6>#0: sun4i-CODECAudio Codec
[*][ 3.020000] #0: sun4i-CODECAudio Codec
[*]<4>EXT2-fs (nandb): warning: mounting unchecked fs, running e2fsck is recommended
[*][ 3.040000] EXT2-fs (nandb): warning: mounting unchecked fs, running e2fsck is recommended
[*]<6>VFS: Mounted root (ext2 filesystem) on device 93:2.
[*][ 3.050000] VFS: Mounted root (ext2 filesystem) on device 93:2.
[*]: sdxc_request_done(L1114): [ 3.060000] : sdxc_request_done(L1114): smc 3 err, cmd 52,RTO !!
[*]smc 3 err, cmd 52,RTO !!
[*]: sdxc_request_done(L1114): [ 3.080000] : sdxc_request_done(L1114): smc 3 err, cmd 52,RTO !!
[*]smc 3 err, cmd 52,RTO !!
[*]: sdxc_request_done(L1114): [ 3.090000] : sdxc_request_done(L1114): smc 3 err, cmd 8,RTO !!
[*]smc 3 err, cmd 8,RTO !!
[*]: sdxc_request_done(L1114): [ 3.100000] : sdxc_request_done(L1114): smc 3 err, cmd 5,RTO !!
[*]smc 3 err, cmd 5,RTO !!
[*]<6>devtmpfs: mounted
[*][ 3.120000] devtmpfs: mounted
[*]: sdxc_request_done(L1114): [ 3.120000] : sdxc_request_done(L1114): smc 3 err, cmd 5,RTO !!
[*]smc 3 err, cmd 5,RTO !!
[*]<6>Freeing init memory: 168K
[*][ 3.130000] Freeing init memory: 168K
[*]: sdxc_request_done(L1114): [ 3.140000] : sdxc_request_done(L1114): smc 3 err, cmd 5,RTO !!
[*]smc 3 err, cmd 5,RTO !!
[*]: sdxc_request_done(L1114): [ 3.150000] : sdxc_request_done(L1114): smc 3 err, cmd 5,RTO !!
[*]smc 3 err, cmd 5,RTO !!
[*]: sdxc_request_done(L1114): [ 3.160000] : sdxc_request_done(L1114): smc 3 err, cmd 55,RTO !!
[*]smc 3 err, cmd 55,RTO !!
[*]: sdxc_request_done(L1114): [ 3.180000] : sdxc_request_done(L1114): smc 3 err, cmd 55,RTO !!
[*]smc 3 err, cmd 55,RTO !!
[*]: sdxc_request_done(L1114): [ 3.190000] : sdxc_request_done(L1114): smc 3 err, cmd 55,RTO !!
[*]smc 3 err, cmd 55,RTO !!
[*]: sdxc_request_done(L1114): [ 3.200000] : sdxc_request_done(L1114): smc 3 err, cmd 55,RTO !!
[*]smc 3 err, cmd 55,RTO !!
[*]: sdxc_request_done(L1114): [ 3.220000] : sdxc_request_done(L1114): smc 3 err, cmd 1,RTO !!
[*]smc 3 err, cmd 1,RTO !!
[*]: mmc 3 power off !!
[*][ 3.230000] : mmc 3 power off !!
[*]mount: mounting devpts on /dev/pts failed: No such file or directory
[*]
[*]Processing /etc/profile... Done
[*]
[*]/ #
[*]
然后呢，我自己弄了我的busyOS，功能：
1.网络DHCP功能，固定mac，和cbos一样
2.安装在nand里，适合嵌入式
3.启动速度快，系统大小370多M（我说下，这个不是系统文件大，是内核大，我把整个cbos的lib复制过来了，包含一堆库和驱动）
4.支持SSh啦！！！终于弄好了，请使用user用户登录而非root，然后su root转到root用户，我用的不是openssh，而是轻量级的dropbear，这个openwrt也在用貌似
5.自动对时，开机时间会长几秒，但是有用
6.还能安装多种pkg，如deb包，rpm包，变得通用了（没有apt-get，只有dpkg！！）
7.功能齐全，unzip啥cmd都有
[*]/ # busybox
[*]BusyBox v1.21.1 (2013-09-14 22:43:52 CST) multi-call binary.
[*]BusyBox is copyrighted by many authors between 1998-2012.
[*]Licensed under GPLv2. See source distribution for detailed
[*]copyright notices.
[*]
[*]Usage: busybox ...]
[*] or: busybox --list[-full]
[*] or: busybox --install [-s]
[*] or: function ...
[*]
[*] BusyBox is a multi-call binary that combines many common Unix
[*] utilities into a single executable.Most people will create a
[*] link to busybox for each function they wish to use and BusyBox
[*] will act like whatever it was invoked as.
[*]
[*]Currently defined functions:
[*] [, [[, acpid, add-shell, addgroup, adduser, adjtimex, arp, arping, ash,
[*] awk, base64, basename, beep, blkid, blockdev, bootchartd, brctl,
[*] bunzip2, bzcat, bzip2, cal, cat, catv, chat, chattr, chgrp, chmod,
[*] chown, chpasswd, chpst, chroot, chrt, chvt, cksum, clear, cmp, comm,
[*] conspy, cp, cpio, crond, crontab, cryptpw, cttyhack, cut, date, dc, dd,
[*] deallocvt, delgroup, deluser, depmod, devmem, df, dhcprelay, diff,
[*] dirname, dmesg, dnsd, dnsdomainname, dos2unix, dpkg, dpkg-deb, du,
[*] dumpkmap, dumpleases, echo, ed, egrep, eject, env, envdir, envuidgid,
[*] ether-wake, expand, expr, fakeidentd, false, fbset, fbsplash, fdflush,
[*] fdformat, fdisk, fgconsole, fgrep, find, findfs, flock, fold, free,
[*] freeramdisk, fsck, fsck.minix, fsync, ftpd, ftpget, ftpput, fuser,
[*] getopt, getty, grep, groups, gunzip, gzip, halt, hd, hdparm, head,
[*] hexdump, hostid, hostname, httpd, hush, hwclock, id, ifconfig, ifdown,
[*] ifenslave, ifplugd, ifup, inetd, init, insmod, install, ionice, iostat,
[*] ip, ipaddr, ipcalc, ipcrm, ipcs, iplink, iproute, iprule, iptunnel,
[*] kbd_mode, kill, killall, killall5, klogd, last, less, linux32, linux64,
[*] linuxrc, ln, loadfont, loadkmap, logger, login, logname, logread,
[*] losetup, lpd, lpq, lpr, ls, lsattr, lsmod, lsof, lspci, lsusb, lzcat,
[*] lzma, lzop, lzopcat, makedevs, makemime, man, md5sum, mdev, mesg,
[*] microcom, mkdir, mkdosfs, mke2fs, mkfifo, mkfs.ext2, mkfs.minix,
[*] mkfs.vfat, mknod, mkpasswd, mkswap, mktemp, modinfo, modprobe, more,
[*] mount, mountpoint, mpstat, mt, mv, nameif, nanddump, nandwrite,
[*] nbd-client, nc, netstat, nice, nmeter, nohup, nslookup, ntpd, od,
[*] openvt, passwd, patch, pgrep, pidof, ping, ping6, pipe_progress,
[*] pivot_root, pkill, pmap, popmaildir, poweroff, powertop, printenv,
[*] printf, ps, pscan, pstree, pwd, pwdx, raidautorun, rdate, rdev,
[*] readahead, readlink, readprofile, realpath, reboot, reformime,
[*] remove-shell, renice, reset, resize, rev, rm, rmdir, rmmod, route, rpm,
[*] rpm2cpio, rtcwake, run-parts, runlevel, runsv, runsvdir, rx, script,
[*] scriptreplay, sed, sendmail, seq, setarch, setconsole, setfont,
[*] setkeycodes, setlogcons, setserial, setsid, setuidgid, sh, sha1sum,
[*] sha256sum, sha3sum, sha512sum, showkey, slattach, sleep, smemcap,
[*] softlimit, sort, split, start-stop-daemon, stat, strings, stty, su,
[*] sulogin, sum, sv, svlogd, swapoff, swapon, switch_root, sync, sysctl,
[*] syslogd, tac, tail, tar, tcpsvd, tee, telnet, telnetd, test, tftp,
[*] tftpd, time, timeout, top, touch, tr, traceroute, traceroute6, true,
[*] tty, ttysize, tunctl, ubiattach, ubidetach, ubimkvol, ubirmvol,
[*] ubirsvol, ubiupdatevol, udhcpc, udhcpd, udpsvd, umount, uname,
[*] uncompress, unexpand, uniq, unix2dos, unlzma, unlzop, unxz, unzip,
[*] uptime, users, usleep, uudecode, uuencode, vconfig, vi, vlock, volname,
[*] wall, watch, watchdog, wc, wget, which, who, whoami, whois, xargs, xz,
[*] xzcat, yes, zcat, zcip
[*]
好了，先这么说，晚点给大家rootfs和安装sh
原文作者：tll
原文链接：http://forum.cubietech.com/forum.php?mod=viewthread&tid=1107
页:
[1]